tag:blogger.com,1999:blog-1268880941558038958.post8966653025350224790..comments2023-02-25T09:36:38.270+00:00Comments on Think3dPrint3d: Basic Marlin Configuration.h modificationTonyhttp://www.blogger.com/profile/10434414082369533349noreply@blogger.comBlogger30125tag:blogger.com,1999:blog-1268880941558038958.post-75004975005836626242017-04-05T01:25:00.154+01:002017-04-05T01:25:00.154+01:00Need help.
Motors engage but dont turn.
Melzi 2.0 ...Need help.<br />Motors engage but dont turn.<br />Melzi 2.0 v5<br />Extruder motor got hot so I turned pots down. Its running repetier, I have installed this programme but dont get it all. <br />Is there a eeprom I can upload that will be close or should I turnt the pots up?<br />Extruder heats up and fan works. Click home all or any on repetier motors will clunk with in secs but not turn.<br /><br />Please advise been searching like mad for week and want this to work.<br />No errors on my lcd. Tried to test run dry it heated up ect but no movement.<br /><br />Please help.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-4402685337224951042015-05-19T13:22:11.090+01:002015-05-19T13:22:11.090+01:00Hello,
Thank you for the useful post. I have a qu...Hello, <br />Thank you for the useful post. I have a question. I am woking with stepper motors and an AzteegX3 PRO 3D board. I want to add a code for managing feedback signal for the motor sensors in case of an error detected. I have no idea how to write a code like this. Do you have some advise?Anonymoushttps://www.blogger.com/profile/08370932960298391918noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-13818505920348950902014-12-11T12:58:48.474+00:002014-12-11T12:58:48.474+00:00My Prusa I3 was going with high speed when homing ...My Prusa I3 was going with high speed when homing and then automacticly went back for aprox. 1cm and then slowly went to the endstop.<br /><br />Yesterday I changed some speed settings, but now homing only goes to the endstop and then nothing.<br />Changing the speed back as before does not help.<br /><br />Now the homing is not as precise as before, which is a problem for the Z axes.<br />I can set the homing speed slower, but found it really nice option that it went back after hitting the endstop and then slowly homed again.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-13546714307579944582014-09-28T04:23:43.463+01:002014-09-28T04:23:43.463+01:00This comment has been removed by the author.Anonymoushttps://www.blogger.com/profile/18243176007948189229noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-90947244155907592162014-08-09T15:54:32.510+01:002014-08-09T15:54:32.510+01:00Depends how well your printer is assembled.. start...Depends how well your printer is assembled.. start with 1000 or 2000 and see how you get on. Tonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-17854674248676810752014-08-09T12:37:35.253+01:002014-08-09T12:37:35.253+01:00What will be the acceleration for the stepper moto...What will be the acceleration for the stepper motor for prusa i2? ?please helpAnonymoushttps://www.blogger.com/profile/15086055513871172973noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-17323248516253608612014-08-05T00:30:54.042+01:002014-08-05T00:30:54.042+01:00In configuration.h find the following line, uncomm...In configuration.h find the following line, uncomment it and then put your name:<br /><br />// #define CUSTOM_MENDEL_NAME "This Mendel"<br /><br />To stop having the "ready"<br /><br />in language.h, find the section that applies to the language you are using and then edit this line (as shown in english):<br /><br />#define WELCOME_MSG MACHINE_NAME " Ready."<br /><br />to remove or replace "ready"<br /><br />Also if you have a board type, 7,71,11, or 80 then look at the top of language.h<br /><br />Cheers<br /><br />TonyTonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-47889905899669974202014-08-05T00:21:36.068+01:002014-08-05T00:21:36.068+01:00Hey Guys, Can Any one guide me to How can I change...Hey Guys, Can Any one guide me to How can I change the name of the Machine from firmware. Like my machine starts and say "Mendel Ready". I want to replace Mendel with my own name. Let me know how can I do that.<br />Thanks!<br />AaltiAnonymoushttps://www.blogger.com/profile/00709022642137961856noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-14925842553215066292014-06-29T20:32:27.775+01:002014-06-29T20:32:27.775+01:00i'm so sorry tony ;o((i'm so sorry tony ;o((<br />Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-17664080393834206842014-06-29T20:29:15.473+01:002014-06-29T20:29:15.473+01:00here:
http://blog.think3dprint3d.com/2013/02/panel...here:<br />http://blog.think3dprint3d.com/2013/02/panelolu2.htmlTonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-88405179025349377202014-06-29T20:26:52.039+01:002014-06-29T20:26:52.039+01:00Hello ?
where are my posts from today ??Hello ?<br /><br />where are my posts from today ??Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-57764478628366725102014-05-14T18:20:00.266+01:002014-05-14T18:20:00.266+01:00Hi Fahim
Glad the blog post helped. I don't b...Hi Fahim<br /><br />Glad the blog post helped. I don't believe such a flow chart exists, Marlin has grown pretty organically and has many features added by individuals to support their specific hardware platforms. The whole codebase is opensource so you can edit any part you want to - the best place to go for support is the Marlin Github pages:<br />https://github.com/ErikZalm/Marlin<br /><br />Cheers<br /><br />Tony<br />Tonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-84857351147655636192014-05-14T00:47:02.223+01:002014-05-14T00:47:02.223+01:00Hello Tony,
Thanks for your informative and well-...Hello Tony,<br /><br />Thanks for your informative and well-structured process presentation here. Your blog has inspired me a lot to do well in my project. I am mechatronics student from Leicestershire and I need to get into the codes of marling firmware and develop according to my needs.<br /><br />I am desperately looking for the flow-chart of the marlin firmware and possibly the ways to edit the libraries.<br /><br />Could you kindly please help me in this matter ??<br /><br />With Regards<br /><br />FahimAnonymoushttps://www.blogger.com/profile/10962930315067329255noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-64180823904751473052013-11-27T08:08:47.455+00:002013-11-27T08:08:47.455+00:00cheers Tony, I'm sure this is just a small thi...cheers Tony, I'm sure this is just a small thing but on upload I get this error arduino-0023\hardware/tools/avr/etc/avrdude.conf:4 unrecognized character: "<"<br /> Anonymoushttps://www.blogger.com/profile/00495995712386724628noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-92138255620378896132013-11-25T20:43:15.129+00:002013-11-25T20:43:15.129+00:00Hey Macroneus
If you have installed the Sanguino ...Hey Macroneus<br /><br />If you have installed the Sanguino extensions into arduino 0023 then you should have "Sanguino W/ Atmega 1284P 16Mhz" as an option, this is what the Melzi uses.<br /><br />For the Z height in Marlin go to "#define Z_MAX_POS 200" and set to "#define Z_MAX_POS 203.6"<br /><br />Tonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-1910841603754045412013-11-25T20:37:43.342+00:002013-11-25T20:37:43.342+00:00hi Tony, ok back to it not sure what line in need ...hi Tony, ok back to it not sure what line in need to change to configure my Z height nophead supply's line 178 #define Z_HOME_POS (203.6) also theirs no melzi under tools/board. Anonymoushttps://www.blogger.com/profile/00495995712386724628noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-12796668219189977002013-11-10T20:23:56.304+00:002013-11-10T20:23:56.304+00:00Hey, on my phone if you go to the arduino website ...Hey, on my phone if you go to the arduino website and link to previous versions you should find it thereTonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-3091434328086681392013-11-10T17:51:15.101+00:002013-11-10T17:51:15.101+00:00Nophead Mendel90, Melzi with Arduino 1.01. the ard...Nophead Mendel90, Melzi with Arduino 1.01. the arduino link you supplied seems to only offer 1.05, if you have a direct link to 0023 then please post.<br />thanks again Tony for your time and innovation. Anonymoushttps://www.blogger.com/profile/00495995712386724628noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-14778759550381652912013-11-10T15:17:02.466+00:002013-11-10T15:17:02.466+00:00Hi Macroneus are you using Arduino 0023 and the Sa...Hi Macroneus are you using Arduino 0023 and the Sanguino version linked in this blog post?<br /><br />I guess you are using a Melzi?Tonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-15655747889660025572013-11-10T11:24:17.732+00:002013-11-10T11:24:17.732+00:00Thanks Tony,
more compiling errors I'm afraid....Thanks Tony,<br />more compiling errors I'm afraid.<br />Marlin_main.cpp:201: error: 'analogInputToDigitalPin' was not declared in this scopeAnonymoushttps://www.blogger.com/profile/00495995712386724628noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-67778353032206465992013-11-10T01:24:34.532+00:002013-11-10T01:24:34.532+00:00Hi macroneus
In the T3P3 version just set the E s...Hi macroneus<br /><br />In the T3P3 version just set the E steps here:<br /><br />DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,655} //655 is esteps per mm<br /><br />Cheers<br /><br />TonyTonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-39858034363835756272013-11-10T00:50:54.175+00:002013-11-10T00:50:54.175+00:00in nopheads configuration.h i can enter my E_STEPS...in nopheads configuration.h i can enter my E_STEPS_PER_MM only lines 4, 5 are missing in t3p3 as a result when compiling i get this error ConfigurationStore.cpp: In function 'void Config_ResetDefault()':<br />ConfigurationStore.cpp:216: error: 'E_STEPS_PER_MM' was not declared in this scope.Anonymoushttps://www.blogger.com/profile/00495995712386724628noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-55893753484855439942013-10-03T13:44:27.810+01:002013-10-03T13:44:27.810+01:00Joakim
Glad you found it helpful and good to see ...Joakim<br /><br />Glad you found it helpful and good to see more hardware supported.Tonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-10916593171998524822013-10-03T13:42:48.168+01:002013-10-03T13:42:48.168+01:00Thank you for an extremely useful blogpost. I'...Thank you for an extremely useful blogpost. I'm now running Think3DPrint3D version of Marlin on my Reprappro Huxley with a 20x4 display and rotary encoder. Would have been very difficult without this blogpost. My display-setup is explained <a href="http://diycrap.blogspot.no/2013/08/i2c-display-and-rotary-encoder-on-melzi.html" rel="nofollow">here</a>.Joakimhttp://diycrap.blogspot.comnoreply@blogger.comtag:blogger.com,1999:blog-1268880941558038958.post-45170276552138497802013-05-21T23:29:11.576+01:002013-05-21T23:29:11.576+01:00Hi Alan
I have emailed you through the work that ...Hi Alan<br /><br />I have emailed you through the work that Icare Design did - I have not had a chance to test it yet and incorporate it.<br /><br />TonyTonyhttps://www.blogger.com/profile/10434414082369533349noreply@blogger.com